Taper bushes
Characteristics
Assembly
Make sure that the tapered surfaces are clean, free of oils or powders.
Place the bushes in the wheel so as to align the holes.
Place the screws into the threaded holes, loosely.
Clean the transmission shaft and then mount the wheel and the bushes, pointing out that the bushes holds the transmission shaft first and then the wheel. With a hex key tighten the screws gradually and alternately.
Check the closing of the screws after a short period of operation.
Disassembly
Loosen all the screws and remove one or two screws depending on the holes of the disassembly.
Insert the screws into the holes for dismantling. Tighten the screws alternately until the relaxation of the bushes. Continue until the group is not free on the transmission shaft.
Remove the bushes and the wheel from the transmission shaft.
BUSHING 1008 | |||
---|---|---|---|
Outer diameter (D1) = 35 | |||
Length (L) = 22.3 | |||
Screws BSW = 1/4 " | |||
Tightening torque = 5,6 Nm | |||
holes diam. | width of the spline | height of spline | Kg. |
d | B | T2 | |
11 | 4 | 1,8 | 0,13 |
12 | 4 | 1,8 | 0,12 |
14 | 5 | 2,3 | 0,12 |
15 | 5 | 2,3 | 0,11 |
16 | 5 | 2,3 | 0,11 |
18 | 6 | 2,8 | 0,10 |
19 | 6 | 2,8 | 0,10 |
20 | 6 | 2,8 | 0,09 |
22 | 6 | 2,8 | 0,08 |
24 | 8 | 1,3 | 0,07 |
25 | 8 | 1,3 | 0,07 |
BUSHING 1108 | |||
---|---|---|---|
Larger diameter (D1) = 38 | |||
Length (L) = 22.3 | |||
Screws BSW = 1/4 " | |||
Tightening torque = 5,6 Nm | |||
holes diam. | width of the spline | height of spline | Kg. |
d | B | T2 | |
11 | 4 | 1,8 | 0.16 |
12 | 4 | 1,8 | 0.15 |
14 | 5 | 2,3 | 0.15 |
15 | 5 | 2,3 | 0.14 |
16 | 5 | 2,3 | 0.14 |
18 | 6 | 2,8 | 0.13 |
19 | 6 | 2,8 | 0.13 |
20 | 6 | 2,8 | 0.12 |
22 | 6 | 2,8 | 0.11 |
24 | 8 | 3,3 | 0.1 |
25 | 8 | 3,3 | 0.09 |
28 | 8 | 1,3 | 0.07 |
BUSHING 1210 | |||
---|---|---|---|
Larger diameter (D1) = 47 | |||
Length (L) = 25,4 | |||
Screws BSW = 3/8 " | |||
Tightening torque = 20 Nm | |||
holes diam. | width of the spline | height of spline | Kg. |
d | B | T2 | |
11 | 4 | 1,8 | 0,28 |
12 | 4 | 1,8 | 0,28 |
14 | 5 | 2,3 | 0,27 |
15 | 5 | 2,3 | 0,26 |
16 | 5 | 2,3 | 0,26 |
18 | 6 | 2,8 | 0,25 |
19 | 6 | 2,8 | 0,24 |
20 | 6 | 2,8 | 0,24 |
22 | 6 | 2,8 | 0,22 |
24 | 8 | 3,3 | 0,21 |
25 | 8 | 3,3 | 0,21 |
28 | 8 | 3,3 | 0,18 |
30 | 8 | 3,3 | 0,17 |
32 | 10 | 3,3 | 0,15 |
BUSHING 1215 | |||
---|---|---|---|
Larger diameter (D1) = 47 | |||
Length (L) = 38,1 | |||
Screws BSW = 3/8 " | |||
Tightening torque = 20 Nm | |||
holes diam. | width of the spline | height of spline | Kg. |
d | B | T2 | |
14 | 5 | 2,3 | 0,38 |
16 | 5 | 2,3 | 0,37 |
18 | 6 | 2,8 | 0,35 |
19 | 6 | 2,8 | 0,34 |
20 | 6 | 2,8 | 0,34 |
22 | 6 | 2,8 | 0,32 |
24 | 8 | 3,3 | 0,29 |
25 | 8 | 3,3 | 0,29 |
28 | 8 | 3,3 | 0,26 |
30 | 8 | 3,3 | 0,23 |
32 | 10 | 3,3 | 0,20 |
BUSHING 1610 | |||
---|---|---|---|
Larger diameter (D1) = 57 | |||
Length (L) = 25,4 | |||
Screws BSW = 3/8 " | |||
Tightening torque = 20 Nm | |||
holes diam. | width of the spline | height of spline | Kg. |
d | B | T2 | |
12 | 4 | 1,8 | 0,41 |
14 | 5 | 2,3 | 0,41 |
15 | 5 | 2,3 | 0,40 |
16 | 5 | 2,3 | 0,40 |
18 | 6 | 2,8 | 0,39 |
19 | 6 | 2,8 | 0,38 |
20 | 6 | 2,8 | 0,38 |
22 | 6 | 2,8 | 0,37 |
24 | 8 | 3,3 | 0,36 |
25 | 8 | 3,3 | 0,35 |
28 | 8 | 3,3 | 0,32 |
30 | 8 | 3,3 | 0,30 |
32 | 10 | 3,3 | 0,29 |
35 | 10 | 3,3 | 0,26 |
38 | 10 | 3,3 | 0,23 |
40 | 12 | 3,3 | 0,21 |
42 | 12 | 3,3 | 0,19 |
BUSHING 1615 | |||
---|---|---|---|
Larger diameter (D1) = 57 | |||
Length (L) = 38,1 | |||
Screws BSW = 3/8 " | |||
Tightening torque = 20 Nm | |||
holes diam. | width of the spline | height of spline | Kg. |
d | B | T2 | |
14 | 5 | 2,3 | 0,58 |
16 | 5 | 2,3 | 0,58 |
18 | 6 | 2,8 | 0,56 |
19 | 6 | 2,8 | 0,55 |
20 | 6 | 2,8 | 0,55 |
22 | 6 | 2,8 | 0,53 |
24 | 8 | 3,3 | 0,50 |
25 | 8 | 3,3 | 0,49 |
28 | 8 | 3,3 | 0,47 |
30 | 8 | 3,3 | 0.45 |
32 | 10 | 3,3 | 0,41 |
35 | 10 | 3,3 | 0,38 |
38 | 10 | 3,3 | 0,32 |
40 | 12 | 3,3 | 0,29 |
42 | 12 | 2,2 | 0,26 |
BUSHING 2012 | |||
---|---|---|---|
Larger diameter (D1) = 70 | |||
Length (L) = 31,8 | |||
Screws BSW = 7/16 " | |||
Tightening torque = 31 Nm | |||
holes diam. | width of the spline | height of spline | Kg. |
d | B | T2 | |
15 | 5 | 2,3 | 0,78 |
16 | 5 | 2,3 | 0,78 |
18 | 6 | 2,8 | 0,76 |
19 | 6 | 2,8 | 0,76 |
20 | 6 | 2,8 | 0,75 |
22 | 6 | 2,8 | 0,74 |
24 | 8 | 3,3 | 0,72 |
25 | 8 | 3,3 | 0,71 |
28 | 8 | 3,3 | 0,68 |
30 | 8 | 3,3 | 0,66 |
32 | 10 | 3,3 | 0,64 |
35 | 10 | 3,3 | 0,60 |
38 | 10 | 3,3 | 0,57 |
40 | 12 | 3,3 | 0,54 |
42 | 12 | 3,3 | 0,51 |
45 | 14 | 3,8 | 0,46 |
48 | 14 | 3,8 | 0,40 |
50 | 14 | 3,8 | 0,37 |
BUSHING 2517 | |||
---|---|---|---|
Larger diameter (D1) = 85 | |||
Length (L) = 44,5 | |||
Screws BSW = 1/2 " | |||
Tightening torque = 48 Nm | |||
holes diam. | width of the spline | height of spline | Kg. |
d | B | T2 | |
19 | 6 | 2,8 | 1,62 |
20 | 6 | 2,8 | 1,60 |
22 | 6 | 2,8 | 1.57 |
24 | 8 | 3,3 | 1.57 |
25 | 8 | 3,3 | 1,56 |
28 | 8 | 3,3 | 1,52 |
30 | 8 | 3,3 | 1,49 |
32 | 10 | 3,3 | 1,45 |
35 | 10 | 3,3 | 1.40 |
38 | 10 | 3,3 | 1.40 |
40 | 12 | 3,3 | 1,35 |
42 | 12 | 3,3 | 1,27 |
45 | 14 | 3,8 | 1,20 |
48 | 14 | 3,8 | 1,13 |
50 | 14 | 3,8 | 1,08 |
55 | 16 | 4,3 | 0,96 |
60 | 18 | 4,4 | 0,81 |
65 | 18 | 4,4 | 0,65 |
BUSHING 3020 | |||
---|---|---|---|
Larger diameter (D1) = 108 | |||
Length (L) = 50,8 | |||
Screws BSW = 5/8 " | |||
Tightening torque = 90 Nm | |||
holes diam. | width of the spline | height of spline | Kg. |
d | B | T2 | |
25 | 8 | 3.3 | 2.91 |
28 | 8 | 3.3 | 2.79 |
30 | 8 | 3.3 | 2.84 |
32 | 10 | 3.3 | 2.80 |
35 | 10 | 3.3 | 2.75 |
38 | 10 | 3.3 | 2.67 |
40 | 12 | 3.3 | 2.64 |
42 | 12 | 3.3 | 2.59 |
45 | 14 | 3.8 | 2.52 |
48 | 14 | 3.8 | 2.43 |
50 | 14 | 3.8 | 2.37 |
55 | 16 | 4.3 | 2.23 |
60 | 18 | 4.4 | 2.07 |
65 | 18 | 4.4 | 1.89 |
70 | 20 | 4.9 | 1.69 |
75 | 20 | 4.9 | 1.49 |
BUSHING 3030 | |||
---|---|---|---|
Larger diameter (D1) = 108 | |||
Length (L) = 76,2 | |||
Screws BSW = 5/8 " | |||
Tightening torque = 90 Nm | |||
holes diam. | width of the spline | height of spline | Kg. |
d | B | T2 | |
35 | 10 | 3.3 | 3.95 |
38 | 10 | 3,3 | 3.86 |
40 | 12 | 3,3 | 3.82 |
42 | 12 | 3,3 | 3.69 |
45 | 14 | 3,8 | 3.55 |
48 | 14 | 3,8 | 3.45 |
50 | 14 | 3,8 | 3.42 |
55 | 16 | 4,3 | 3.18 |
60 | 18 | 4,4 | 2.95 |
65 | 18 | 4,4 | 2.68 |
70 | 20 | 4,9 | 2.38 |
75 | 20 | 4,9 | 2.03 |
BUSHING 3525 | |||
---|---|---|---|
Larger diameter (D1) = 127 | |||
Length (L) = 64,9 | |||
Screws BSW = 1/2 " | |||
Tightening torque = 112 Nm | |||
holes diam. | width of the spline | height of spline | Kg. |
d | B | T2 | |
35 | 10 | 3.3 | 4.91 |
38 | 10 | 3,3 | 4,85 |
40 | 12 | 3,3 | 4,80 |
42 | 12 | 3,3 | 4,71 |
45 | 14 | 3,8 | 4,67 |
48 | 14 | 3,8 | 4,55 |
50 | 14 | 3,8 | 4,44 |
55 | 16 | 4,3 | 4,29 |
60 | 18 | 4,4 | 4,05 |
65 | 18 | 4,4 | 3,88 |
70 | 20 | 4,9 | 3,58 |
75 | 20 | 4,9 | 3,37 |
80 | 22 | 5,4 | 3,05 |
85 | 22 | 5,4 | 2,77 |
90 | 25 | 5,4 | 2,47 |
BUSHING 3535 | |||
---|---|---|---|
Larger diameter (D1) = 127 | |||
Length (L) = 88,9 | |||
Screws BSW = 1/2 " | |||
Tightening torque = 112 Nm | |||
holes diam. | width of the spline | height of spline | Kg. |
d | B | T2 | |
35 | 10 | 3.3 | 6.7 |
38 | 10 | 3,3 | 6,53 |
40 | 12 | 3,3 | 6,48 |
42 | 12 | 3,3 | 6,40 |
45 | 14 | 3,8 | 6,25 |
48 | 14 | 3,8 | 6,17 |
50 | 14 | 3,8 | 6,05 |
55 | 16 | 4,3 | 5,81 |
60 | 18 | 4,4 | 5,50 |
65 | 18 | 4,4 | 5,20 |
70 | 20 | 4,9 | 4,88 |
75 | 20 | 4,9 | 4,46 |
80 | 22 | 5,4 | 4,08 |
85 | 22 | 5,4 | 3,67 |
90 | 25 | 5,4 | 3,21 |
BUSHING 4040 | |||
---|---|---|---|
Larger diameter (D1) = 146 | |||
Length (L) = 101,8 | |||
Screws BSW = 5/8 " | |||
Tightening torque = 170 Nm | |||
holes diam. | width of the spline | height of spline | Kg. |
d | B | T2 | |
45 | 14 | 3,8 | 9.86 |
48 | 14 | 3,8 | 9.66 |
50 | 14 | 3,8 | 9.48 |
55 | 16 | 4,3 | 9.27 |
60 | 18 | 4,4 | 8.93 |
65 | 18 | 4,4 | 8.65 |
70 | 20 | 4,9 | 8.17 |
75 | 20 | 4,9 | 7.78 |
80 | 22 | 5,4 | 7.35 |
85 | 22 | 5,4 | 6.89 |
90 | 25 | 5,4 | 6.36 |
95 | 25 | 5.4 | 5.94 |
100 | 28 | 6.4 | 5.27 |
BUSHING 4545 | |||
---|---|---|---|
Larger diameter (D1) = 162 | |||
Length (L) = 114,3 | |||
Screws BSW = 3/4" | |||
Tightening torque = 192 Nm | |||
holes diam. | width of the spline | height of spline | Kg. |
d | B | T2 | |
55 | 16 | 4,3 | 13.15 |
60 | 18 | 4,4 | 12.76 |
65 | 18 | 4,4 | 12.38 |
70 | 20 | 4,9 | 12.02 |
75 | 20 | 4,9 | 11.57 |
80 | 22 | 5,4 | 11.05 |
85 | 22 | 5,4 | 10.46 |
90 | 25 | 5,4 | 9.99 |
95 | 25 | 5.4 | 9.42 |
100 | 28 | 6.4 | 8.63 |
110 | 28 | 6.4 | 7.37 |
BUSHING 5050 | |||
---|---|---|---|
Larger diameter (D1) = 178 | |||
Length (L) = 127 | |||
Screws BSW = 7/8" | |||
Tightening torque = 271 Nm | |||
holes diam. | width of the spline | height of spline | Kg. |
d | B | T2 | |
70 | 20 | 4,9 | 16.7 |
75 | 20 | 4,9 | 16.05 |
80 | 22 | 5,4 | 15.56 |
85 | 22 | 5,4 | 15.00 |
90 | 25 | 5,4 | 14.43 |
95 | 25 | 5.4 | 13.88 |
100 | 28 | 6.4 | 13.05 |
110 | 28 | 6.4 | 11.56 |
120 | 32 | 7.4 | 9.78 |
125 | 32 | 7.4 | 9.05 |